發布時間: 2017-06-21 點擊次數: 4536次
特種防盜門使用說明書
產品簡介
我公司是社會(huì )公共安全防范產品的生產廠家。由我公司研制生產的特種防盜門,吸收了*技術,研制出該款防盜性能良好的特種防盜門。
門框門扇采用鋼板折彎焊接成型,堅固、抗沖擊性能良好 。
本產品采用四面多個防撬鎖點固定,鎖舌從四個面伸進,把門扇和門框連成牢固的整體,大大增強了防盜性能。
所有門體、門框采用先進的處理工序,經過除酸、除銹、除油、磷化(采用無磷磷化劑)、中和處理,表面靜電噴涂粉末涂料。
產品示意圖
三、安裝步驟:
1、土建房:
1.1、將門置于門洞內,調整門框兩側立框的垂直度(全長不大于2 毫米)及門框的對角線長度(兩對角線長度差不大于2.5毫米)。并用木楔將門框初步固定。
1.2、用馬仔將門框固定,并再次檢查門框兩側立框的垂直度及門框對角線長度差。
1.3、開關門扇,調整門扇和鎖都能開啟自如。
1.4、用水泥砂漿將門框與墻體之間的縫隙填滿并抹平,如圖A處。
2、板建機房:
1.1、將門置于門洞內,調整門框兩側立框的垂直度(全長不大于2 毫米)及門框的對角線長度(兩對角線長度差不大于2.5毫米)。并用木楔將門框初步固定。
1.2、在門框四角(B面上)打上一顆柳釘,開關門扇,調整門扇和鎖都能開啟自如。
1.3、在門框B面均勻加打鉚釘將門*固定。
四、開啟方法:
1.開門:
1.1進門:用鑰匙打開鎖,旋轉手輪,打開門。
1.2出門:旋轉旋扭開關,旋轉把手,打開門
2.鎖門:
順時針旋轉手輪至轉不動,拔出鑰匙,順、逆時針交替旋轉手輪,手輪轉動不了,鎖門完成。
注意:手輪轉得動則門未鎖上,需重復上面步驟,直至手輪轉不動。
五、鎖具接線
紅線:DC12V電源正極
棕色:DC12V電源負極
白色:門磁信號
藍色:鎖閉信號
淡藍色:鎖舌狀態信號
黃色:開鎖信號
六、保養
1.在安裝過程中有碰傷涂層的,需補漆處理,防止生銹。
2.鉸鏈C三個月需加一次潤滑油,鎖舌及鎖機構活動部位半年需加一次潤滑油。
七、包裝
本產品將門框與門扇組裝成一體,上下兩端再用瓦楞紙袋套住,并用包
帶捆緊,可防止門體相互碰撞,鑰匙掛在門框側面。
八、貯藏及運輸:
本產品在貯藏及運輸過程中均應豎立放置,與鉛垂面的夾角不應大于15度,并應將各門的鎖(或手柄)左右錯開擺放,以防產品之間的相互碰撞。
在貯藏及運輸過程中應防雨淋、跌落及碰撞。門的底部應有固定物(如下
圖)阻止產品滑動。運輸時,應在門的中部用繩索加以固定。