Product category
門安裝說明書
一、產品簡介
門是消防設備中的重要組成部分,是社會(huì )中的重要一環,因此門的質量和使用問題是關系著成敗的關鍵。
鋼質門是指用冷軋薄鋼板作門框、門板、骨架,在門扇內部填充不燃材料,并配以五金件所組成的,能滿足耐火穩定性、完整性和隔熱性要求的門。按耐火極限區分,有、乙級和丙級三種門。
二、產品示意圖
三、技術參數:
1、本產品門框、門扇分別采用3mm、1.5mm冷軋鋼板, 使用先進技術和工藝生產制作出堅固、美觀之產品。
2、本產品可根據需要提供不同的外觀顏色。
3、采用鎖、閉門器、鉸鏈,保證一定的防盜性能。
4、本產品門扇內部填充無無害隔熱材料。
四、安裝步驟:
1、 量洞口是否與安裝規格相符:框寬度比洞口尺寸小20毫米為宜,高度上減10毫米灰口,不帶下檻框,下加30毫米預埋,即帶下檻框高度比洞口小10毫米,不帶下檻框,框高比洞口高20毫米(已含30毫米預埋),帶下檻框應分清上、下,合頁孔距框斷面距離短者為上。
2、 在門框上固定好連接鐵,將巖棉塞在鎖孔、順序器孔、閉門器孔位置及上亮子裝玻璃壓條處,并在門框內填充200#細石混凝土,也可用珍珠巖混凝土填充,既可減輕門框重量又可省去填充巖棉工序?;炷凉潭ê?,將框按所需方向放入洞口。
3、 門框經初步固定,用吊線或水平尺進行調整,要求門框前后、左右垂直度≤2mm,對角線差≤2mm,無下檻框、上角要找方。
4、 門框找正后,把門框上連接鐵與預埋鐵焊牢,若洞口沒有預埋件,可用射釘或膨脹螺栓把連接件固定在墻上。
5、 門框檢驗無誤后,去掉附加支撐,用200#細石混凝土塞滿門框與洞口間隙,并按施工要求掩框口,刷漿?! ?/span>
6、 安裝門扇時要保證上縫及邊縫均勻,縫隙小于或等于3mm,門扇開關靈活,帶插銷門扇,插銷開關自如,不擺動。先用十字螺絲刀把合頁固定在門扇上。把門扇掛在門框上。掛門時,先將門扇豎放在門框合頁邊框旁,與門框成90°夾角,為安裝方便,門扇底部可用木塊墊起。對準合頁位置,將門扇通過合頁固定在門框上?! ?/span>
7、五金配件安裝:安裝五金配件及有關裝置。門扇關閉后,門縫應均勻平整,開啟自由輕便,不得有過緊、過松和反現象?! ?nbsp;
8、 噴塑框在安裝前應在框表面粘膠帶紙以保護表面涂層。
9、門框安裝墻體中間,若墻體過寬,應保證框開啟面到墻面距離應小于或等于110毫米,防止墻角碰閉門器,若門扇要求開180度,門框開啟面應與墻面平。
10、 門框、門扇在安裝過程中應保證清潔,洞口刷漿完畢后,噴漆門應再刷兩遍漆,噴塑門應把框上不干膠撕掉并用清水擦凈,zui后在框口上粘上膠條。
五、保養
1.在安裝過程中有碰傷涂層的,需補漆處理,防止生銹。
2.鉸鏈三個月需加一次潤滑油、鎖舌及鎖機構活動部位半年需加一次潤滑油。
六、包裝
本產品將門框與門扇組裝成一體,上下兩端再用瓦楞紙袋套住,并用包帶捆緊,可防止門體相互碰撞,鑰匙掛在門框側面。
七、貯藏及運輸:
本產品應貯存在通風、干燥處,要避免和有腐蝕的物質及氣體接觸,并要采取防潮、防雨、防曬、防腐等措施,產品平放時底部須墊平,門框堆碼高度不得超過1.5m,門扇堆放高度不超過1.2m,產品豎放時,其傾斜角度不得大于20°。運輸時,應在門的中部用繩索加以固定。
七、產品實物圖
聯系我們
深圳市龍電興業科技有限公司 公司地址:深圳市寶安區石巖街道應人石社區三和工業區A棟 技術支持:智慧城市網掃一掃 更多精彩
微信二維碼