Product category
防弾門是一種能吸收和耗散弾頭、破片的動能,阻止弾頭、破片穿透,有效保護門內人員、物資安全,并符合一定的防弾安全級別的門。
安裝防弾門前需先測量門洞尺寸,根據樓道確定開啟方向。門洞尺寸應大于所安裝門的尺寸,并留有一定的余隙(大約1.5-3cm),方便安裝時調試校正。
修正門洞,門洞尺寸不符合要求須用鐵鍾、鋼鑿、切割機等工具切割、修平以達到安裝要求。
安裝時把門放進門洞,四周用木栓塞緊,校正水平和垂直度,調試好是否開啟靈活,然后打開門扇,用電錘通過門框安裝孔中鉆好安裝孔,逐個用膨脹栓緊固好。
膨脹栓鉆進墻壁的深度要≥5cm,沖擊電錘的鉆頭需和膨脹栓尺寸符合。工程安裝時業主或建筑方需標出50cm的水平線或100cm水平線,用戶單獨安裝須確定地面鋪地磚或地板高度。門安裝完畢后,門框兩側需灌入一定量的水泥沙漿(一般達到70%以上),修補墻壁灌沙漿等由用戶自己負責完成。
防弾門安裝注意事項:
(1)防弾門的安裝應按照所采用的防弾門種類,采取相適應的安裝方法。
(2)防弾門的門框可以采用膨脹螺栓與墻體固定,也可以在砌筑墻體時在洞口處預埋鐵件,安裝時與門框連接件焊牢。
(3)門框與墻體不論采用何種連接方式,每邊均不應少于3個錨固點,且應牢固連。
(4)安裝防弾門時,應先找直、吊正,尺寸量合適后將其臨時固定,并進行校正、調整,無誤后方可以進行連接錨固。
(5)要求推拉門安裝后推拉靈活;平開門開啟方便,關閉嚴密牢固。
(6)門框與門扇之間或其它部位應安裝防盜裝置。
(7)防弾門上的拉手、門鎖、觀察孔等五金配件,必須齊全;多功能防弾門上的密碼護鎖、電子報警密碼系統、門鈴傳呼等裝置,必須有效完善。
(8)要求與地平面的間隙應不大于5mm。
深圳市龍電興業科技有限公司嚴格按照Q/BJABYT012—2010《防弾門通用技術條件》規定生產制作防弾門,憑借先進的技術、的研發、現代化的生產一直走在行業的前沿。
聯系我們
深圳市龍電興業科技有限公司 公司地址:深圳市寶安區石巖街道應人石社區三和工業區A棟 技術支持:智慧城市網掃一掃 更多精彩
微信二維碼