發布時間: 2019-09-23 點擊次數: 1915次
泄爆門窗在避難所、變電所、控制室上都會(huì )安裝,是為了阻隔爆炸源危害,但在選購時一定要認真謹慎,必須安裝通過認可的多項認證和檢測的。
泄爆窗口潛在爆炸危險的地區,這樣的建筑物可以是一個單獨的區域或沿外墻,旨在將損害程度降低到低水平。泄爆窗口提供室內爆燃封閉爆炸壓力,并能即刻緩解臨界壓力通風裝置。注意:爆炸性物質燃燒速率小于聲音的速度,爆震發生時的系統功能,沖擊波和壓力達到初的爆炸集開啟壓力發泄窗戶自動打開,及時的沖擊和壓力發泄在室外,以避免建筑物和其他設施的破壞,保持建筑結構的完整性。在使用后,通風窗可以關閉檢測可重復使用。
對于泄爆門收貨時應認真按供貨合同核對數量、規格、等級及各種配件是否、齊全。保管、貯存窗應垂直存放于干燥的室內,并要有防腐措施,玻璃應擱置和依靠在不能損傷玻璃邊緣和玻璃面的物體上。
泄爆門窗安裝之前必須進行檢查,如因運輸貯存不慎導致窗框、窗扇翹曲、變形、玻璃破損,應修復后方可進行安裝。
安裝前應檢查產品有無翹曲、脫膠現象,如有要及時修理,產品進場后,未安裝前應放置通風干燥處,碼放整齊,入露天堆放時,要用雨布蓋好,不準日曬雨淋。
線定位:按設計要求尺寸、標高和開啟方向,畫出窗框中心位置線。
不論采用何種連接方式,每邊均不應少于3個連接點,且應牢固連接。
打孔下漲栓:根據控制線在墻的立面打孔,每邊不少于3點且中間的間距不得大于600mm,距上下口不大于200mm,塞入Ф8膨脹螺栓并上緊。
窗框固定:窗框與墻體固定可采用膨脹螺栓、射釘或與預埋或后置的鐵件焊接的方式進行。
窗框內灌漿:需要在窗框內填充細石混凝土,填充前應先把窗關好,將窗扇開啟面的窗框與窗扇之間的防漏孔塞上塑料蓋后,方可進行填充,填充水泥不能過量,防止窗框變形影響開啟。
安裝五金:五金配件安裝均應符合消防規范要求并達到各自的使用功能,安裝零附件宜在墻面裝飾后進行,安裝時應按廠方的說明進行,如需先安裝,應注意防止污染和丟失、損壞,密封條應在門窗涂料干燥后,按型號進行安裝和壓實。
窗洞口處理:安裝前檢查窗洞口尺寸,偏位、不垂直、不方正的要進行剔鑿或抹灰處理。
窗框與墻體間隙間的處理:窗框周邊縫隙,用1:2的水泥砂漿或強度不低于C20的細石混凝土嵌縫牢固,應保證與墻體結成整體,經養護凝固后,再粉刷洞口及墻體。窗框與墻體連接處打建筑密封膠。