發布時間: 2020-03-13 點擊次數: 2110次
密閉防潮防盜門用于井下材料庫和材料發放硐室,起隔離作用阻止沖擊波及產生的火焰、有氣體向外部巷道擴散,由總回風道排出,由門框、門扇、閉鎖裝置、餃頁等部件組成。
門框為不等邊角組焊框架結構,門扇上部裝有三組通風活門裝置,即在活門底板開有三組共18個直徑122mm的通風孔,活門板外部裝有自動張開12度角的活門懸板。每組活門通風量為2000立方/h,總通風量為6000立方/h,風速按8m/s進行設計,使用時可根據井下爆破材料庫需要風量和總回風道負壓值,確定通風活門組數,并可調節每組活門懸板的張啟角度進行微調,以滿足通風量。
當庫內一旦發生爆炸,沖擊波經過衰減后,余壓只要大于20KPa時,活門懸板受壓再3-8s內自動關閉,與外界隔離,組織爆炸抗沖擊波及爆炸產生火焰,有氣體向外部巷道擴散,由總回風道排出。密閉防潮防盜門設置2組,一組為通常關閉用的閉鎖軸,手柄轉動式;另一組為緊急閉鎖裝置,其功能是當沖擊力大于294N時,瞬間,門與門框緊閉,壓縮密封圈,鎖頭進入鎖芯,撥動雙片簧,制動閉鎖,防止門反;撥動外鑰匙手柄即可解除閉鎖。
密閉防潮防盜門要求
1、開啟應向庫內,抗沖擊波密閉門設計采用向右側開啟方向,若要向左側開啟,則應以門扇中心線為軸,對稱變動零件位置。
2、門扇頁板安裝,應保證上、下鉸頁孔同心,中心線平行于門扇內表面中心線。
3、門框與墻洞為一整體,澆灌混凝土之前,應將鉸頁的固定角鋼檢查、較正、固定牢靠,保證上、下鉸頁孔在中心在一條垂直線上,不同中心度允許誤差為2mm。
4、門扇安裝后與門框平面應貼合,并成垂直面,局部間隙在3mm以?xún)取?nbsp;
5、閉鎖、鉸頁的活動部位應經常注入油脂,各部件應至少每年維修保養一次。
6、外露金屬表面應涂紅丹防銹漆二遍,桔紅色面漆兩遍,并在門扇外表面標出把手開 關方向。
7、為吊裝門扇,門洞頂棚應相應預埋吊環一個。
8、密封膠條與門扇連接,先用 萬能膠粘合,然后用螺栓固定。
9、密封膠條應經常涂滑石粉,防止老化。