陜西省延安市珠寶金庫門生產廠家
簡要描述:陜西省延安市珠寶金庫門廠家
產品型號:
所屬分類:珠寶店金庫門
更新時間:2023-04-25
廠商性質:生產廠家
詳情介紹
陜西省延安市珠寶金庫門生產廠家
金庫門的特點/金庫門 編輯
1、防盜性強。
2、門鎖安全系數高,一般采用雙鎖、高難度多重密碼鎖。
3、造型穩重、質量重。
4、、防毀性能的高。
陜西省延安市珠寶金庫門廠家
金庫門的標準/金庫門 編輯
本產品嚴格按照中華人民共和國公共安全行業標準《GA/T143-1996金庫門通用技術條件》和中華人民共和國金融行業標準《JR/T 0001-2000金庫門》設計制造。
“鑫瑞”牌金庫門不僅具有標準型金庫門的、防潮、防盜、焰切割、防鉆、防沖擊等各種功能,還具備(A/B/C)三種防護級別。
產品采用寶鋼鋼板,其鋼板的強度與鋼筋水泥混凝土的強度相等,因此其堅固性無異于鋼筋水泥混凝土,堪稱“銅墻鐵壁”,無懈可擊,門板里面有、防鉆、焰切割材料。[1]
陜西省延安市珠寶金庫門廠家
金庫門密碼鎖/金庫門 編輯
1、《利用開啟標志打開金庫門》
如果密碼鎖的出廠密碼為50,則向左轉刻度盤,直到數字50通過開啟標志四次,并對準開啟標志。再向右轉動至刻度盤停止,此時密碼鎖舌收回,即可打開金庫門。
用隨意密碼號打開金庫門,例如10-20-30。
向左轉動刻度盤至少4個整圈,以清除原密碼并接受新密碼。
向左轉動刻度盤,直至*個密碼數字10通過開啟標記三次后,于第四次準確地停在標記上。
向右轉動刻度盤,直至第二個密碼數字20通過開啟標記二次后,于第三次準確地停在標記上。
向左轉動刻度盤,直至第三個密碼數字30通過開啟記一次后,于第二次準確地停在標記上。
向右轉動刻度盤,直至鎖打開(不要將刻度盤朝右轉得太多)。鎖密碼鎖時,向左轉動刻度盤4圈以上。
2、《利用改碼標記來改變密碼》
要改變密碼,必須知道原來的密碼和需要一把改碼鑰匙。
在改變密碼之前,先用原密碼10-20-30打開金庫門。然后象前述開啟方法一樣,以改碼標記來調原密碼10-20-30,而且刻度碼盤應停在密碼的zui后一位數字30處。
把改碼鑰匙插入背面的匙孔,如果改碼鑰匙不能插入,說明密碼未對好應重復上述過程再做一次。
向右轉動改碼鑰匙至它停止(近似1/4轉),鑰匙留在鎖上。選擇一組新的密碼,如40-50-60。注意密碼的末號數不要選擇0到20的數字(禁止區)。
向左轉動刻度盤,直至數字“40”通過改碼標記三次,于第四次準確地停在改碼標記上。
向右轉動刻度盤,直至數字“50”通過改碼標記二次,于第三次準確地停在改碼標記上。
向左轉動刻度盤,直至數字“60”通過改碼標記一次,于第二次準確地停在改碼標記上。
向左轉動改碼鑰匙至停止,然后拿去鑰匙。
留言詢價